BLIŻSZE SPOJRZENIE
Trochę więcej o tym produkcie
Setting Intensity With the Fluence LED Dimmer Controller
Product details
- A dimmer is the part of a Fluence room that most growers bolt on after the fixtures are already hanging.
- This one is a single-channel wall unit outputting either a 0-10V analog signal or a PWM signal, set by a switch on the housing.
- It leaves the factory pre-set to the analog signal, so a room running Fluence drivers works on first power-up without anyone touching that switch.
- Intensity covers the full 0 to 100% range and the digital readout shows the number rather than a vague dial position.
- Source and sink current is rated at 40 mA DC, and that current is what caps the chain.
- Fluence now puts the recommended ceiling at 25 fixtures, or 32 mA of loading, across no more than 200 feet of signal wire.
- Run the wire longer than that and signal strength falls off, which quietly reduces how many fixtures actually track the dimmer.
- The unit takes 120V AC and runs on 12 VDC at 0.5 A through a barrel connector.
- Two 2-position terminal connectors land the dimming signal wires, and one of them is a spare.
- Mounting the Grow Light Dimmer and What Ships With It
- Mount it on a wall near the fixtures rather than out by the door, because the signal-wire budget gets spent fast in a long room.
- Screws and drywall anchors come in the box.
- Keep it clear of the wet zone and anything that gets splashed during irrigation, and dry your hands before touching the buttons.
- Fluence rates it for spaces under eighty percent relative humidity, which rules out a lot of flower rooms at lights-out.
- A wall in a dry corridor outside the canopy is the usual answer.
- The LiPo backup battery holds the intensity setting through a short outage, so the room comes back where you left it instead of at full.
- This unit ships with its power cord, and Fluence has confirmed that the AC wall adapter is sold separately.
- That adapter is Fluence part DM2AA-DPA1BCMTAP, and without it the dimmer has no wall power.
- Growers running a combined power and dimming whip can skip it, since the fixture feeds the dimmer down the same cable.
- It is not a timer, so photoperiod still belongs to a contactor or an AC timer upstream.
- The dimming signal cable is a separate item too, and which one depends on whether the fixture takes M12 or M16.
- Dual Signal Output: Pushes either a 0-10V analog or a PWM signal, chosen with a switch on the housing.
- Digital Intensity Readout: Shows the exact set point instead of leaving you guessing at a dial position.
- Battery-Backed Setting: A LiPo cell holds your intensity level through a brief outage so nothing resets to full.
- Chain Capacity: Fluence rates a recommended 25 fixtures at 32 mA of loading over 200 feet of signal wire.
- Wall-Mount Hardware Included: Screws, drywall anchors and two terminal connectors ship in the box, one of them a spare.
- Fluence Fixture Compatibility: Works with SPYDR 1 and 2, VYPR 3, RAY, RAZRm, RAZRx and RAZR 2 through 4.
- Technical Specifications
Specyfikacje
- Model
- Fluence Whisper 2.0 Dimmer (AC/DC)
- Dimming Signals
- 0-10V ±0.1V or PWM 0-100% ±1%
- Dimming Range
- 0-100% light intensity
- Recommended Fixture Count
- 25 units (32 mA, 80% max loading)
- Input Power
- 120V AC, 60 Hz
- Dimensions
- 3.92 in L x 3.43 in W x 1.35 in H
- Weight
- 5 oz (142 g)
- Operating Humidity
- Below 80% RH
- Fixture Compatibility
- SPYDR 1, SPYDR 2, VYPR 3, RAY, RAZRm, RAZRx, RAZR 2/3/4
- Dual Signal Output
- Pushes either a 0-10V analog or a PWM signal, chosen with a switch on the housing.
- Chain Capacity
- Fluence rates a recommended 25 fixtures at 32 mA of loading over 200 feet of signal wire.
- Wall-Mount Hardware Included
- Screws, drywall anchors and two terminal connectors ship in the box, one of them a spare.
- Fluence Fixture Compatibility
- Works with SPYDR 1 and 2, VYPR 3, RAY, RAZRm, RAZRx and RAZR 2 through 4.
Pytania i dyskusja
Masz pytanie lub chcesz się czymś podzielić? Rozpocznij rozmowę.